Menu
I have been working on my 6.5HP push mower motor. I looked on B&S.com and they didn't have my manual my model number is 1-82. The issues that I am having are I can spray starter fluid to fire it up but it shuts down right afterwards. I was able today to get it running but I had to hold the lever that attaches to the flapper in the carb than goes to a lever on the EXH end of the ENG in the closed position on the carb.
![]()
I was told today that it was the choke. I have noticed that when the ENG runs a while the flapper tends to stay open. Can anyone give me some guidance or some hints on where to get a manual to help me out. Thanks in advance.
Been there seen that. Just trying to help a friends sister out. She's a single mother. Installed a new magnetto the other day. Just not sure if the choke spring is in the right spot. International harvester 966 manuals.
Had to stretch it to get it to run at a decent rpm.Her brotheresd fiddled with stuff. A picture of the choke arm and spring would be nice. Been there seen that. Just trying to help a friends sister out. She's a single mother. Installed a new magnetto the other day.
Just not sure if the choke spring is in the right spot. Had to stretch it to get it to run at a decent rpm.Her brotheresd fiddled with stuff. A picture of the choke arm and spring would be nice.
![]()
Check that electrical outlet for the washer. Plug a small lamp or appliance into that outlet to make sure that it works properly. That part 137005020 is the correct replacement control board for that washer. The reed switch for that dispenser is no longer used on that new control board. You can just position those dispenser drawer wires out of the way. The wiring diagram for that washer is shown in the image below with the voltage supply for that control board traced in red and green (actual wire colors black and white).
I recommend that you carefully check the voltage on those wires at the control board using a volt/ohm meter. NOTE: You should only check that live voltage if you are completely confident in your technical ability to safely measure it. Wear proper safety equipment (electrical safety gloves and safety goggles) when checking that live voltage. Unplug the washer as soon as that live testing is completed. If that control is getting voltage but will not power up then the replacement control board could be defective or you could have a short in one of the washer components that is dragging down voltage on the board so that it won't power up.
126t02 0675 B2 Engine
If you are not getting voltage at that connection then you could have a bad outlet cord or a wiring failure in between the outlet cord connection and the control board. These tips may help you determine the cause of this failure. If you need more help, reply with additional details.
If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link:. FREE Standard Shipping on orders of $90 or more Purchase requirement calculated before taxes and shipping charges and after other discounts have been applied and must be made in a single transaction. 2017 fat bob cvo service manual. Cannot be applied to previous purchases and cannot be redeemed for cash. Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands. Offer valid for online purchases only. In an event of a return, coupon savings may be deducted from your refund. Discount will be automatically applied during check-out.
Briggs And Stratton Ohv Manual
Sears Holdings reserves the right to terminate or modify this offer at any time for failure to comply with its terms and/or due to any operational malfunction of the software, hardware or equipment required to process this offer. © 2013 Sears Brands, LLC. May not be used with any other coupon, associate discount, or during Family & Friends or Member events.
Briggs & Stratton Model 42a707 Repair Manual
365 Day Return Policy You may return an unused and uninstalled part in its original packaging. To return a part, enter your order number/zipcode above and continue through the return process to obtain a Return Authorization number. We must receive the returned part(s) with the Return Authorization number within 365 days of your original order date. Exclusions apply to products with limited shelf life, which includes but are not limited to batteries, smoke detectors, or chemical based products; these products must be returned within 90 days of the original order date. Items received damaged must be reported within 10 days of receipt.
Credit will be issued for the part(s) plus tax, minus any shipping charges.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |